Ross Video LimitedCrossOverUser ManualSoftware Issue: v1.4
1–2 • Introduction CrossOver 6 / 12 User Manual (v1.4)Ô Switcher InstallationControl PanelThe switcher control panel is designed to sit on a desk or t
CrossOver 6 / 12 User Manual (v1.4) Introduction • 1–33. Menu Screen and Knobs• Rotate a knob to change the menu option displayed above it.• Press the
1–4 • Introduction CrossOver 6 / 12 User Manual (v1.4)Ô Frame Rear Connections OverviewFigure 1.6 CrossOver 12Figure 1.7 CrossOver 61. Power Connect
CrossOver 6 / 12 User Manual (v1.4) Introduction • 1–5corresponding menu, the menu is automatically displayed.Menu NavigationSome menus have multiple
1–6 • Introduction CrossOver 6 / 12 User Manual (v1.4)sides of the Lens must be at the sides of the text on the Insert Film.4. Aligning the notches on
CrossOver 6 / 12 User Manual (v1.4) Configuration • 2–1ÔConfigurationThis chapter describes how to configure your switcher to meet your requirements.
2–2 • Configuration CrossOver 6 / 12 User Manual (v1.4)Ô Format Conversion and Frame SyncThe switcher has four input format converter / frame synchron
CrossOver 6 / 12 User Manual (v1.4) Configuration • 2–3the image is stretched/compressed to fit in the new aspect ratio.• Zoom — The central portion o
2–4 • Configuration CrossOver 6 / 12 User Manual (v1.4)• The switcher is set to switch on the first field when using Bus mode.• If a video format not
CrossOver 6 / 12 User Manual (v1.4) Configuration • 2–53. Press NEXT until OSync is displayed.4. Use the OSync knob to select the reference output you
Ô CrossOver • User Manual• Ross Part Number: 4801DR-002• Document Issue: 1C• Release Date: May 26, 2009. Printed in Canada.• Software Issue: v1.4The i
2–6 • Configuration CrossOver 6 / 12 User Manual (v1.4)Ô Input BNC ConfigurationMany video sources have an associated video source that contains alpha
CrossOver 6 / 12 User Manual (v1.4) Configuration • 2–75. Use the AnMode knob to set the appearance of the analog output. You can choose from the foll
2–8 • Configuration CrossOver 6 / 12 User Manual (v1.4)5. Press the IP Addr knob to display the IP Address menu.6. Use the IPMode knob to select Stati
CrossOver 6 / 12 User Manual (v1.4) Configuration • 2–9Note:• It is not recommended to set the Panel Glow color to red. Red indicates a source is on-a
2–10 • Configuration CrossOver 6 / 12 User Manual (v1.4)3. Press the right knob to set the switcher power-save behavior. You can choose from the follo
CrossOver 6 / 12 User Manual (v1.4) Configuration • 2–11are asked if you wish to take the first Chroma Key off-air and use the Chroma Key resource for
2–12 • Configuration CrossOver 6 / 12 User Manual (v1.4)To set the Next Transition area reset behavior:1. Press MENU.2. Press the PERS Wipe Pattern bu
CrossOver 6 / 12 User Manual (v1.4) Basic Operation • 3–1ÔBasic OperationThis chapter describes the general operation of your switcher. Basic informat
3–2 • Basic Operation CrossOver 6 / 12 User Manual (v1.4)1. Select the source you want to take on-air by pressing a source button on the Program bus.N
CrossOver 6 / 12 User Manual (v1.4) Basic Operation • 3–3Ô Keying OverviewKeying allows you to insert portions of one scene into another. Keys appear
Ô Important Safety InstructionsWarning 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not
3–4 • Basic Operation CrossOver 6 / 12 User Manual (v1.4)•Press CUT to immediately cut the selected source on-air (selected transition type is ignored
CrossOver 6 / 12 User Manual (v1.4) Basic Operation • 3–53. If you have already assigned a Chroma Key to one of the other keyers and the Chroma Key sh
3–6 • Basic Operation CrossOver 6 / 12 User Manual (v1.4)To change the pattern:1. Press and hold SHIFT.2. Press BLACK/MATTE to display the Matte menu.
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–1ÔAdvanced OperationThis chapter describes advanced operating concepts for your switcher. A
4–2 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)1. Press RECALL.2. Select the memory register you wish to recall from as follows:• If you
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–3Recall to Preview Off• Scenario 1› Input 3 is recalled to the Program bus (on-air image in
4–4 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)performed with the Fader will stop when it reaches the defined limit. To define the transi
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–5To configure user-defined defaults:1. Configure any of the settings in the previous list a
4–6 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)When resetting a key, the selected Chroma Key color and any Split Key assignments are not
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–77. Use the left knob to select which memory registers you wish to save. You can choose fro
23.Certain parts of this equipment still present a safety hazard with the power switch in the OFF position. To avoid electrical shock, disconnect all
4–8 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)10. Press the Confrm knob to perform the load. Press the Cancel knob to cancel the load.No
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–9A mask is a keying technique in which a pattern is combined with the key source to block o
4–10 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)Modifying Clip and Gain for Unshaped Auto-Select KeysIf an Auto-Select key is unshaped, y
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–11Chroma Key is taken off-air and converted to an Auto-Select Key.•Press the Cancel knob to
4–12 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)To modify time and direction:1. Press WIPE to display the Wipe menu.2. Press NEXT until T
CrossOver 6 / 12 User Manual (v1.4) Advanced Operation • 4–131. Press AUX SEL to display the Aux menu.2. Select an Aux bus by pressing the correspondi
4–14 • Advanced Operation CrossOver 6 / 12 User Manual (v1.4)Ô General Purpose Interface (GPI)The switcher has 24 GPI inputs that are used to trigger
CrossOver 6 / 12 User Manual (v1.4) Media-Store • 5–1ÔMedia-StoreThis chapter describes the Media-Store operation. Your switcher has 2 Media-Store cha
5–2 • Media-Store CrossOver 6 / 12 User Manual (v1.4)8. Navigate to sub-directories by selecting a sub-directory name and then pressing the left knob.
CrossOver 6 / 12 User Manual (v1.4) Media-Store • 5–31. If you are loading from a USB drive, insert it into the USB port on the switcher.2. Press and
Ô Warranty and Repair PolicyRoss Video Limited (Ross) warrants its switchers and related options, to be free from defects under normal use and service
5–4 • Media-Store CrossOver 6 / 12 User Manual (v1.4)1. Press and hold SHIFT on any bus. If you use the Program bus or on-air Key bus, you will affect
CrossOver 6 / 12 User Manual (v1.4) Media-Store • 5–57. Use the Valu e knob to set the reverse playback behavior. You can choose from the following:•
5–6 • Media-Store CrossOver 6 / 12 User Manual (v1.4)
CrossOver 6 / 12 User Manual (v1.4) Specifications • 6–1ÔSpecificationsÔ DimensionsFrame:• Width: 19” (fits standard equipment rack)• Depth: 15.63”• H
6–2 • Specifications CrossOver 6 / 12 User Manual (v1.4)Reference Input and Output SpecificationsTri-level Pulse• Input Return Loss: ≥30dB to 30 MHz•
CrossOver 6 / 12 User Manual (v1.4) Specifications • 6–3Write Fade To Black Rate—* 5 FD ** *Currently not supported. Fade to black rate is the same as
6–4 • Specifications CrossOver 6 / 12 User Manual (v1.4)Key Matte Border Lum Keyer 0x1A Key mattes not supportedKey Matte Fill Lum Keyer 0x1B Key matt
CrossOver 6 / 12 User Manual (v1.4) Specifications • 6–5Key Bus On Air Keyer 0x2A Turning OFF results in a protocol error.Key Video FillKeyer 0x2F Alw
6–6 • Specifications CrossOver 6 / 12 User Manual (v1.4)Dsk Preview— 0x1E Always true. All Keyers show on preview.Fade To Black 0x1FKey Bus 0-9 Keyer
CrossOver 6 / 12 User Manual (v1.4) iÔContentsIntroduction 1About This Manual ... 1-1Documentation Terms...
ii CrossOver 6 / 12 User Manual (v1.4)
CrossOver 6 / 12 User Manual (v1.4) Introduction • 1–1ÔIntroductionThe CrossOver 6 and CrossOver 12 combine professional switcher quality with an easy
Comments to this Manuals