Ross CrossOver 6 Operator's Manual Page 52
- Page / 86
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4–10 • Advanced Operation CrossOver 6 / 12 User Manual (v4.0)
› NoRst — The Aux bus is not included in
the reset.
9. Press NEXT until RState Save is
displayed.
10. Press the RState Save knob to save the
new default settings.
11. Press the Confrm knob to commit the save.
Press the Cancel knob to cancel the save
and return to the previous setting.
Restoring Default Settings to Factory State
You can restore user-defined default settings to a
factory state. This is useful if you wish to begin
creating a new user-defined default from a known
starting configuration.
To restore user-defined default settings to the
factory state:
1. Press MENU.
2. Press the RESET Wipe Pattern button.
3. Press NEXT until RState Dfault is
displayed.
4. Press the RState Dfault knob to restore the
user-defined defaults to factory settings.
5. Press the Confrm knob to commit the
change. Press the Cancel knob to cancel the
change and return to the previous setting.
Resetting the Switcher
Resetting the switcher restores the user-defined
default settings.
To reset the switcher:
1. Press and hold MENU.
2. Press the RESET Wipe Pattern button.
To reset the switcher using an alternate method:
1. Press MENU.
2. Press the RESET Wipe Pattern button.
3. Press the RState Load knob.
All switcher settings are restored to the
user-defined default values.
Shared Parameters
Some parameters are shared between features and if
reset in one area, are reset in all areas that share that
parameter. The shared parameters are:
• Time — This value is shared between dissolves,
wipes, and DVE transitions.
• Limit — This value is shared between dissolves,
wipes, and DVE transitions.
• Pattern (Pattrn) — This value is shared between
wipes and mattes.
Resetting Individual Settings
You can reset individual settings to user-defined
default values rather than resetting the entire
switcher.
To reset wipes:
1. Press and hold down WIPE.
2. Press the RESET Wipe Pattern button.
To reset dissolves:
1. Press and hold down DISS.
2. Press the RESET Wipe Pattern button.
To reset Key 1:
1. Press and hold down CHR KEY, AUTO
SELECT, or DVE.
2. Press the RESET Wipe Pattern button.
Note:
• The selected Chroma Key color and any Split Key
assignments are not reset.
To reset Key 2 or 3:
1. Press and hold down KEY 2 SEL or KEY 3
SEL.
2. Press the RESET Wipe Pattern button.
When resetting a key, the selected Chroma Key
color and any Split Key assignments are not
reset.
Note:
• The selected Chroma Key color and any Split Key
assignments are not reset.
To reset Aux buses:
1. Press and hold down AUX SEL (CrossOver 6)
or AUX 1 or AUX 2 or AUX 3 (CrossOver 12).
2. Press the RESET Wipe Pattern button.
NEXT
MENU
NEXT
MENU
MENU
- CrossOver 6 1
- CrossOver 12 1
- Operator’s Manual 1
- Important Safety Instructions 3
- EMC Notices 4
- Warranty and Repair Policy 5
- Environmental Information 5
- Company Address 6
- Contents 7
- What’s New 9
- Introduction 11
- Control Panel Overview 12
- Frame Overview 13
- Removing the Frame Door 14
- Menu System 14
- Button Inserts 15
- Positioner 16
- Selecting Colors 16
- Configuration 17
- 4 knob to assign the FCFS 19
- 4 knob to save your 19
- knob to save your 20
- Aspect Ratio 21
- Ancillary Data 21
- Input BNC Configuration 22
- Clean Feed 22
- MultiViewer 23
- CrossOver CleanSwitch 24
- IP Address 24
- Switcher Personality 25
- To specify resource sharing: 27
- For More Information on 28
- Chroma Key Resource Capturing 28
- DVE Resource Capturing 28
- Basic Operation 31
- Wipe Transitions 32
- DVE Transitions 32
- Media Transitions 33
- Pausing a Transition 33
- Keying Overview 34
- Key Transitions 34
- Dedicated Key Transitions 35
- UltraChrome Chroma Key 36
- Fade to Black 42
- Advanced Operation 43
- Modifying DVE Transitions 44
- Advanced Keying 45
- Aux Buses 47
- Creating an FTP Connection 48
- TC timecode data: 50
- Reset Options 51
- Device Control 53
- 13 12 11 10 9 8 7 6 5 4 3 2 1 56
- 141516171819202122232425 56
- Triggering GPI Outputs 57
- Transition Pre-Delay 59
- Editor Port 59
- Table 4.7 Editor Port Pinout 60
- Memories, USB Storage, and 61
- Upgrades 61
- Storing Memory Registers 64
- Recalling Memory Registers 64
- USB Storage 66
- Software Upgrades 68
- Media-Store 69
- Loading Media by Browsing 70
- Loading Media by FTP 70
- Understanding Media Numbers 71
- Loading Media by Media Number 71
- Media-Store Attributes 72
- Animation Control 73
- Calibration and Diagnostics 75
- Error Messages 77
- Specifications 79
- GVG Editor Input Mapping 80
Relacionado con productos y manuales para Herramientas Ikea ESSVIK AA-291709-1
(12 paginas)© 2020, manymanuals.com. All rights reserved. | 0.601 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals