Ross CrossOver 6 Operator's Manual Page 57
- Page / 86
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CrossOver 6 / 12 User Manual (v4.0) Advanced Operation • 4–15
7. Use the Type knob to select the GPI output
level and trigger type. You can choose from the
following:
• LowE — The output level is
set high, and momentarily
goes low for the trigger.
• HighE — The output level is
set low, and momentarily goes
high for the trigger.
• LowL — The output level
toggles from the base high
level to the low level. The
output signal remains at this
level until reset
• HighL — The output toggles
from the base low level to the
high level. The output signal
remains at this level until
reset.
8. If you selected either LowE or HighE in the
previous step, use the Dur knob to set the
length (in frames) that the GPI output remains
triggered.
Note:
• Edge triggered GPI outputs remain triggered for
the configured duration.
• Level triggered GPI outputs toggle between
latched and unlatched each time you press the
corresponding Wipe Pattern button.
• Changing the configuration of a GPI output pin
that is currently latched causes it to unlatch.
GPI Input Banks
Banks configured as GPI inputs have inputs assigned
as follows (Pin 1 is the top right pin when looking at
the GPI Port).
Figure 4.5 GPI Port
Note:
• GPI input pin assignments are not
user-configurable.
For More Information on...
• port locations, refer to the section “Frame Rear
Connections Overview” on page 1-3.
Triggering GPI Outputs
You can trigger GPI outputs manually or
automatically.
Table 4.5 GPI Port GPI Input Mapping
Pin Trigger
Bank 1
1 Dissolve Key 1
2 Dissolve Key 2
3 Dissolve Key 3 (CrossOver 12 only)
4 Perform Auto Transition
Trigger
Duration
Trigger
Duration
Trigger
Trigger
13 12 11 10 9 8 7 6 5 4 3 2 1
141516171819202122232425
5 Perform Program / Preset Bus cut
6 Perform Key 1 cut
7 Perform Key 2 cut
8 Perform Key 3 cut (CrossOver 12 only)
Bank 2
9 Perform Fade to Black
10 Set Aux Bus 1 to Input 1
11 Set Aux Bus 1 to Input 2
12 Set Aux Bus 1 to Input 3
13 Set Aux Bus 1 to Input 4
14 Set Aux Bus 1 to Input 5
15 Recall Memory 0
a
16 Recall Memory 1
a
Bank 3
17 Recall Memory 2
a
18 Recall Memory 3
a
19 Recall Memory 4
a
20 Recall Memory 5
a
21 Recall Memory 6
a
22 Recall Memory 7
a
23 Recall Memory 8
a
24 Recall Memory 9
a
Not Assigned to a Bank
25 Ground
a. Only memory registers from memory bank 0 can be recalled with a
GPI trigger.
Table 4.5 GPI Port GPI Input Mapping
Pin Trigger
- CrossOver 6 1
- CrossOver 12 1
- Operator’s Manual 1
- Important Safety Instructions 3
- EMC Notices 4
- Warranty and Repair Policy 5
- Environmental Information 5
- Company Address 6
- Contents 7
- What’s New 9
- Introduction 11
- Control Panel Overview 12
- Frame Overview 13
- Removing the Frame Door 14
- Menu System 14
- Button Inserts 15
- Positioner 16
- Selecting Colors 16
- Configuration 17
- 4 knob to assign the FCFS 19
- 4 knob to save your 19
- knob to save your 20
- Aspect Ratio 21
- Ancillary Data 21
- Input BNC Configuration 22
- Clean Feed 22
- MultiViewer 23
- CrossOver CleanSwitch 24
- IP Address 24
- Switcher Personality 25
- To specify resource sharing: 27
- For More Information on 28
- Chroma Key Resource Capturing 28
- DVE Resource Capturing 28
- Basic Operation 31
- Wipe Transitions 32
- DVE Transitions 32
- Media Transitions 33
- Pausing a Transition 33
- Keying Overview 34
- Key Transitions 34
- Dedicated Key Transitions 35
- UltraChrome Chroma Key 36
- Fade to Black 42
- Advanced Operation 43
- Modifying DVE Transitions 44
- Advanced Keying 45
- Aux Buses 47
- Creating an FTP Connection 48
- TC timecode data: 50
- Reset Options 51
- Device Control 53
- 13 12 11 10 9 8 7 6 5 4 3 2 1 56
- 141516171819202122232425 56
- Triggering GPI Outputs 57
- Transition Pre-Delay 59
- Editor Port 59
- Table 4.7 Editor Port Pinout 60
- Memories, USB Storage, and 61
- Upgrades 61
- Storing Memory Registers 64
- Recalling Memory Registers 64
- USB Storage 66
- Software Upgrades 68
- Media-Store 69
- Loading Media by Browsing 70
- Loading Media by FTP 70
- Understanding Media Numbers 71
- Loading Media by Media Number 71
- Media-Store Attributes 72
- Animation Control 73
- Calibration and Diagnostics 75
- Error Messages 77
- Specifications 79
- GVG Editor Input Mapping 80
© 2020, manymanuals.com. All rights reserved. | 0.496 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals