Ross CrossOver 6 Operator's Manual Page 75
- Page / 86
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CrossOver 6 / 12 User Manual (v4.0) Calibration and Diagnostics • 7–1
Calibration and Diagnostics
This chapter describes how to check the version of
software on the switcher, copy switcher logs to a
USB, perform calibration and systems tests, as well
as what the error messages reported by the switcher
mean.
Switcher Software Version
The Status menu shows the version number of the
software that is currently running on the control
panel and frame.
To view the current version of software on the
switcher:
1. Press MENU.
2. Press the STATUS Wipe Pattern button.
The current software version (SW Ver) and
reference format is shown on the menu.
Copy Logs to USB
The Copy Logs allows you to store switcher logs
onto a USB. Switcher logs can be used by technical
support to diagnose problems with your switcher.
To copy switcher logs to USB:
1. Insert it into the USB port on the switcher. Wait
5 seconds after inserting the USB drive before
using it.
2. Press MENU > SYSTEM >
NEXT > NEXT.
3. Press the Diag Tests knob.
4. Press NEXT.
5. Press the Copy Logs knob. The logs are
copied to the root directory of the USB.
Calibration
Calibration allows you to reset the limits of the
faders on the control panel and re-center the
positioner with X and Y limits.
To calibrate the positioner and fader:
1. Press MENU > SYSTEM >
NEXT > NEXT.
2. Press the Diag Tests knob.
3. Press NEXT.
4. Press the Calib Reset knob.
5. Move the positioner backwards and forwards
and left to right a few times.
6. Move the fader from one limit to the next a few
times. Do not push the fader hard when it
reaches the limit.
7. Press MENU to save the calibration
information.
Diagnostics
Diagnostics consist of a number of tests that are used
to test the functionality of a number of switcher
functions.
Control Test
The Control Test allows you to test the functionality
of any of the buttons, knobs or fader and positioner
on the control panel.
To test control panel control surfaces:
1. Press MENU > SYSTEM >
NEXT > NEXT.
2. Press the Diag Tests knob.
3. Press the Contrl Test knob. The second line
of the display show the current button, knob,
positioner, or fader being used.
4. Test the button, knob, positioner, and fader you
want to check.
5. Press the MENU and RESET buttons
at the same time to end the test.
MENU
MENU
NEXT
NEXT
NEXT
MENU
NEXT
NEXT
NEXT
MENU
MENU
NEXT
NEXT
MENU
- CrossOver 6 1
- CrossOver 12 1
- Operator’s Manual 1
- Important Safety Instructions 3
- EMC Notices 4
- Warranty and Repair Policy 5
- Environmental Information 5
- Company Address 6
- Contents 7
- What’s New 9
- Introduction 11
- Control Panel Overview 12
- Frame Overview 13
- Removing the Frame Door 14
- Menu System 14
- Button Inserts 15
- Positioner 16
- Selecting Colors 16
- Configuration 17
- 4 knob to assign the FCFS 19
- 4 knob to save your 19
- knob to save your 20
- Aspect Ratio 21
- Ancillary Data 21
- Input BNC Configuration 22
- Clean Feed 22
- MultiViewer 23
- CrossOver CleanSwitch 24
- IP Address 24
- Switcher Personality 25
- To specify resource sharing: 27
- For More Information on 28
- Chroma Key Resource Capturing 28
- DVE Resource Capturing 28
- Basic Operation 31
- Wipe Transitions 32
- DVE Transitions 32
- Media Transitions 33
- Pausing a Transition 33
- Keying Overview 34
- Key Transitions 34
- Dedicated Key Transitions 35
- UltraChrome Chroma Key 36
- Fade to Black 42
- Advanced Operation 43
- Modifying DVE Transitions 44
- Advanced Keying 45
- Aux Buses 47
- Creating an FTP Connection 48
- TC timecode data: 50
- Reset Options 51
- Device Control 53
- 13 12 11 10 9 8 7 6 5 4 3 2 1 56
- 141516171819202122232425 56
- Triggering GPI Outputs 57
- Transition Pre-Delay 59
- Editor Port 59
- Table 4.7 Editor Port Pinout 60
- Memories, USB Storage, and 61
- Upgrades 61
- Storing Memory Registers 64
- Recalling Memory Registers 64
- USB Storage 66
- Software Upgrades 68
- Media-Store 69
- Loading Media by Browsing 70
- Loading Media by FTP 70
- Understanding Media Numbers 71
- Loading Media by Media Number 71
- Media-Store Attributes 72
- Animation Control 73
- Calibration and Diagnostics 75
- Error Messages 77
- Specifications 79
- GVG Editor Input Mapping 80
© 2020, manymanuals.com. All rights reserved. | 1.993 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals